null
Created with Sketch.
Skip to main content

By: Motobilt

Motobilt Hammer Series Front Bumper with Stinger & Fogs (Wrangler JK 2007-2018)

SKU: MTB-MB1025F-S
Free Ground Shipping within the Contiguous US

The Motobilt Jeep JK Front The Hammer Bumper is a 48.5 inch wide, sleek, tight-fitting design proudly made in the USA. Our JK The Hammer Bumper is 3D CAD designed to ensure the best possible fit to your Jeep JK. The bumper will fit all year models of the Jeep JK 2 door and 4 door JK Unlimited. The front d-ring mounts are CNC cut from 3/4 inch thick steel plate and pass through the bumper where they weld to the bumper mounting plates in addition to the bumper body. This was done for added strength to the recovery point.

The Hammer bumper has provisions to mount the factory fog lights or aftermarket LED fog lights. We have pre-installed riv nuts for 10-24 screws in the factory bolt pattern. The Hammer bumper can be run with or without the optional skid plate. To install the skid plate, you have to trim approx 1 inch off each side of the crash bars. If you remove the skid plate later, the part that you trimmed will not be seen. The ends of the Hammer bumper taper up for tire clearance. Each cut in the bumper was intentional to keep it tight to the frame rail for a better approach angle. The main construction of the bumper is fabricated from 3/16 inch thick high strength steel plate. The bumper also serves as a winch mount. The top side of the JK The Hammer Bumper has bolt holes for a recovery winch.

Kit Includes:
- One (1) front bumper
- Necessary hardware

  • Fabricated from 3/16 inch thick high strength steel plate
  • Bolt on design
  • 3/4 inch thick steel d-ring mounts
  • Pass through d-ring mounts weld to the bumper
  • Pre-installed riv nuts for 10-24 screws in the factory bolt pattern
  • Made in the USA
  • Sold as each

Notes:
** If installing a winch, MB1002 fairlead mount will also need to be purchased. Not included- available separately
*** Ships bare for painting or powder coating prior to installation
**** No cutting required on the frame rails
***** The two outside top bolt holes on your frame need to be drilled out to 9/16
****** 2012-2018 models will need a vacuum pump relocation bracket. Not included- available separately
******* Skid plate sold separately

Fits:
Jeep Wrangler JK 2 Door (2007-2018)
Jeep Wrangler JK 4 Door Unlimited (2007-2018)

5 Star Customer Service
Price Match Guarantee

Not sure what you need?

Product Description

Motobilt Hammer Series Front Bumper with Stinger & Fogs (Wrangler JK 2007-2018)

The Motobilt Jeep JK Front The Hammer Bumper is a 48.5 inch wide, sleek, tight-fitting design proudly made in the USA. Our JK The Hammer Bumper is 3D CAD designed to ensure the best possible fit to your Jeep JK. The bumper will fit all year models of the Jeep JK 2 door and 4 door JK Unlimited. The front d-ring mounts are CNC cut from 3/4 inch thick steel plate and pass through the bumper where they weld to the bumper mounting plates in addition to the bumper body. This was done for added strength to the recovery point.

The Hammer bumper has provisions to mount the factory fog lights or aftermarket LED fog lights. We have pre-installed riv nuts for 10-24 screws in the factory bolt pattern. The Hammer bumper can be run with or without the optional skid plate. To install the skid plate, you have to trim approx 1 inch off each side of the crash bars. If you remove the skid plate later, the part that you trimmed will not be seen. The ends of the Hammer bumper taper up for tire clearance. Each cut in the bumper was intentional to keep it tight to the frame rail for a better approach angle. The main construction of the bumper is fabricated from 3/16 inch thick high strength steel plate. The bumper also serves as a winch mount. The top side of the JK The Hammer Bumper has bolt holes for a recovery winch.

Kit Includes:
- One (1) front bumper
- Necessary hardware

  • Fabricated from 3/16 inch thick high strength steel plate
  • Bolt on design
  • 3/4 inch thick steel d-ring mounts
  • Pass through d-ring mounts weld to the bumper
  • Pre-installed riv nuts for 10-24 screws in the factory bolt pattern
  • Made in the USA
  • Sold as each

Notes:
** If installing a winch, MB1002 fairlead mount will also need to be purchased. Not included- available separately
*** Ships bare for painting or powder coating prior to installation
**** No cutting required on the frame rails
***** The two outside top bolt holes on your frame need to be drilled out to 9/16
****** 2012-2018 models will need a vacuum pump relocation bracket. Not included- available separately
******* Skid plate sold separately

Fits:
Jeep Wrangler JK 2 Door (2007-2018)
Jeep Wrangler JK 4 Door Unlimited (2007-2018)

NEED ASSISTANCE?

NEED ASSISTANCE?
Call us 774-826-9948 Mon - Fri
9 am - 6 pm (Eastern Time)
Email Us Sales@Offroadelements.com Expect a reply
within 24 hours
Visit Us 1209 Bedford Street, Abington, MA 02351 Get Directions
Passion Built Expert Backed

Passion Built
Expert Backed

Since 2011, we’ve lived off-road, bringing know-how to every build.

Local Roots Nationwide Reach

Local Roots
Nationwide Reach

From our MA shop to your driveway, we deliver trusted gear anywhere.

Only Gear We’d Run Ourselves

Only Gear
We’d Run Ourselves

Handpicked from trusted brands for durability, performance, and style.

Your Adventure Our Commitment

Your Adventure
Our Commitment

5-star service, and a team that treats your rig like their own.

My Cart